The 5456 Aluminum For Ship Building

 Ships often sail in harsh sea water media and marine environments, so whether the materials used are corrosion-resistant is a key factor for deciding whether they can be used as the marine aluminum sheets. The aluminum sheets should have no stress corrosion, spalling corrosion, and intergranular corrosion tendency in seawater and marine environments.

Relevant experiments have proved that any small aluminum boat can be used for decades without any obvious corrosion. The exit of such ships is usually due to outdated technology, rather than the aging of the aluminum structure. Therefore, 5xxx aluminum has been recognized for its excellent resistance to marine climate, especially the resistance to seawater erosion. Among them, 5456 aluminum is a typical welding aluminum alloy.

Among non-heat-treated alloys,5456 aluminium sheet has higher strength, good weldability, corrosion resistance and low temperature performance. Its performance can fully meet the requirements of high welding structure. In addition, 5456 aluminium price is very reasonable, contributing to a low shipbuilding cost.

5456 aluminum plate can be used on the side of the ship and will not corrode for a long time. It is also mainly used on ship decks. Depending on the different tempers, it can be used in different positions such as living deck, walking deck, driving deck,etc.

The bottom shell is an integral part of the bottom structure, which is welded from many metal plates to form the shape of the bottom of the ship. Different positions of the ship's bottom plate have different stress positions. It is necessary to choose the appropriate aluminum alloy according to the position.

5456 aluminum is very suitable for being used as the bottom outer pate of the ships. Aluminum alloy 5456 has high toughness and plasticity, and the plasticity of the ship material can effectively prevent the cracks on the hull from increasing that will reduce its hardness. The weldability of 5456 aluminum plate is better than that of steel, and it is a good choice for ship building.

Original Source:https://www.marinealu.com/a/the-5456-aluminum-for-ship-building.html

6061 T6 Aluminum Sheet Vs Aluminium Alloy 7075T6

 In terms of structural metal manufacturing, perhaps there is only one metal that has a similar popularity to steel and that is aluminum. The weight of aluminum is only one-third that of steel, but it also has excellent mechanical properties. But not all aluminum has the same properties, so it is necessary to know their differences.

6061 t6 aluminum sheet and aluminum alloy 7075 t6 are two kinds of aircraft grade aluminum for structural applications. Although they are similar in some respects, there are also big differences.

Alloys and Chemical Composition

6061 aluminum sheet is 6xxx aluminum and 7075 is 7xxx aluminum sheet. 6061 aluminum has a higher silicon content, while 7075 has a higher zinc content. It can also be seen that both alloys contain a large amount of magnesium, but 7075 has a slightly higher magnesium content. 7075 aluminum also contains a large amount of copper.

Mechanical Properties

Both 6061 and 7075 aluminum t6 sheet has been heat treated. The tensile strength of 7075-T6 is almost twice that of 6061-T6. The shear strength of 7075-T6 is about 1.5 times that of 6061-T6. The lower hardness makes aluminum 6061 easier to manufacture than 7075 alloy.

6061 aluminum sheet is weldable while 7075 is generally considered to be non-weldable. Although 6061 is considered to be weldable, we mus choose a proper welding metal. After welding, heat treatment and aging treatment are also required to restore the welding area to the original temper.

Application

Both are used in bicycle parts, aerospace parts and building structures, but their specific uses are different. For example, in the aerospace industry, aluminum alloy 7075 t6 is more likely to be used as a gear or rod, while 6061 is more likely to be used in areas of greater ductility.

7075 aluminum is more used in molds and industrial tools than 6061. Because 6061 is easier to mold than 7075, 6061 is more commonly used for cans and other objects with round shapes.

Original Source:https://www.aircraftaluminium.com/a/6061-t6-aluminum-sheet-vs-aluminium-alloy-7075t6.html

5083 Aluminium Plate Used in Cars

 One of the obvious changes in car technology since the 1970s is the extensive use of light materials, and more and more aluminum parts have appeared such as body in white, engine, bumper, air conditioner, wheel hub, and decorative parts ,seat,etc.

The aluminium alloys in automotive industry include 5182, 5083, 5754, 5052, 6061, 6063, 6082 aluminum sheets, which are used in the tank truck, van, coach and passenger cars. They feature good corrosion resistance, good welding performance, good process performance and good coloring performance. Lets have a look of three main applications of 5083 aluminum plate.

Trunk Lid

Generally speaking, the trunk lid of a car has a good elongation and large opening area. It is a necessary passage for passengers to take luggage, tools and other spare items. 5083 aluminum plate has good wear resistance, corrosion resistance and elasticity, and good impact resistance. With low density and light weight, it can reduce the weight of the car body, thus reducing fuel consumption.

Car Pedals

The material used for car pedals generally chooses the material with higher hardness. The aluminum alloy has low density, but the strength is relatively high, which is close to or exceeds that of high-quality steel.

The use of 5083 aluminum alloy for automobile pedals can meet its requirement for the strength for it has high corrosion resistance, good weldability and medium strength,bringing longer service life to the car pedal.

Van Body

The 5083 aluminum for van boday greatly extends the service life of the ruck for the aluminum alloy plate has good oxidation resistance, corrosion resistance and excellent rust resistance. The lightweight van body allow it carry more goods. Welcome to leave message below to inquire aluminum 5083 price.

Original Source:https://www.autoaluminumsheet.com/a/5083-aluminium-plate-used-in-cars.html

The Application of Aluminium En Aw 5083 in LNG Storage Tank

The aluminium en aw 5083 is widely used in the manufacture of LNG ships and LNG storage tanks, especially in Japan, a country with large liquefied gas. Among them, the main wall structure of the LNG storage tank is 5083 aluminum alloy.

Most aluminum alloys have become important materials for the top structure of storage tanks because of their unique light weight and properties. The use of aluminum alloy to manufacture storage tank top cover has the following characteristics:

1. After the 5083 aluminum alloy is used for the tank top of the LNG storage tank, the weight is greatly reduced, which reduces the load of the tank and its foundation.

2. Aluminum alloy sheet has good corrosion resistance, so it doesn’t need anti-corrosive treatment, which There is no need for maintenance during the use period, which saves a lot of inspection and maintenance costs.

3. The strength of aluminum alloy material is higher at low temperature than normal temperature, and it is an ideal material under low temperature conditions. Therefore, the additional insulation to prevent low temperature brittleness of the material can be omitted during the entire service life.

4. In terms of the actual construction situation, a LNG storage tank is of high economy. It also can reduce the loss of LNG and prevent the liquefied gas from being polluted by water, sand and debris.

5. With a solid roof made of 5083 aluminum plate, it can prevent the the generation of the sparks when it is hit by the direct lightning strike. Haomei aluminum 5083 can fully meets the application materials. Welcome to leave message below to inquire 5083 aluminum sheet price.

Original Source:https://www.aluminumtankerplate.com/a/the-application-of-aluminium-en-aw-5083-in-lng-storage-tank.html

Aluminium Jumbo Roll for Hair Foil

 The hair foil is used to wrap the hair during various perm and dyeing. It has a heat preservation effect, which can shorten the time of hair treatment and avoid the pollution of hairdressing chemicals. It also contributes to the the rich hair styles.

The present aluminum for hairdressing is cut from aluminum jumbo roll with a smooth surface. Some hair foil producer likes to paint the aluminum foils to get different colors. Haomei Alumium offers 1200 and 1235 aluminum foil with different thicknesses. In this month, one of our old British customers just ordered 10 tons of 1235 aluminum foil in 17 microns.

Our aluminum jumbo roll has the following advantages:

1. It is of small specific gravity and low cost.

2. It has high conductivity.

3. It has good thermal conductivity and strong radiation heat insulation ability.

4. It has good air tightness.

5. It has high strength ratio.

6. It is more corrosion resistant in daily environment.

7. It has good cold deformation performance.

8. It is not magnetized.

The Specification of Aluminum Hair Foil Jumbo Roll

Alloy	Temper	Thickness	Inner Diameter	Maximum Outer Diameter
8011	O	0.01-0.025mm	76 mm	500mm
1200	O	0.01-0.025mm	76 mm	500mm
1235	O	0.01-0.025mm	76 mm	500mm

original source: https://www.alumhm.com/a/aluminium-jumbo-roll-for-hair-foil.html

The Versatile 6063 Aluminum Plate

 Alloy 6063 with Mg and Si as main elements has excellent processing properties, excellent weldability, extrudability and electroplating properties, good corrosion resistance, excellent anodizing effect, etc. It is widely used in construction field, elevators, fences,etc.

6063 aluminum alloy has many features: It can be strengthened by heat treatment, has high impact toughness and is insensitive to defects. It has excellent thermoplasticity and can be extruded into a complex structure at high speed. Thin-walled parts (6<3mm) can also be wind quenched.

In addition, it has excellent welding performance and corrosion resistance, no stress corrosion cracking tendency. Among the heat-treatable aluminum alloys, the Al-Mg-Si series alloy is the only alloy that has no stress corrosion cracking phenomenon.

Shipbuilding

The raw material for shipbuilding must have good performance and strong corrosion resistance. 6063 aluminium plate has long service life in the harsh environment, which can meet the requirements of ship production.

Refrigerator

The biggest feature of refrigerator production is its good airtightness. Refrigerators require refrigeration and fresh-keeping effects during use. 6063 aluminum has very good sealing performance.

Aerospace Equipment

The materials used in space equipment must have good performance in the extremely harsh environment. 6063 Aluminum plate is used to make plate fuselage frames, beams, rotors, propellers, fuel tanks, rocket forging rings, spacecraft siding, etc.

Original Source:https://www.aircraftaluminium.com/a/the-versatile-6063-aluminum-plate.html

Marine Grade Aluminum 6061 for Ship Building

 The main alloy elements of marine grade aluminum 6061 are magnesium and silicon, which have medium strength, good corrosion resistance, good weldability, high toughness, no deformation after processing and good anodizing effect. It is widely used for the building of different ships such as catamaran, sailing boats, container and ship deck.

A catamaran is a conjoined ship composed of two slender hulls connected together horizontally. The hulls are connected by a deck bridge and each has an independent propulsion device. As the two small boats are connected horizontally, they can withstand large winds and waves at sea and are not easy to capsize. The light weight, strong mechanical properties and corrosion resistance of aluminum alloy make it widely used in the construction of catamarans.

The sailing boat can move forward only by wind, without having to install a huge fuel tank and internal combustion engine, so that it can free up a lot of space to store the required drinking water and food. At present, most of the sailing boat materials are made of 6061 alloy, which can be used as masts and other marine accessories.

The container format is uniform and can be stacked layer by layer, so it can be placed in large amount on the ocean-going ships to provide cheap transportation service. The aluminum profiles for containers mainly include 6061, 6082, 6351, 6005, 6063 and 6060 alloys, of which 6061 and 6082 sheets are the most used, accounting for more than 90% of the usage.

The deck is an important component of the hull. It is a plane structure above the inner bottom plate in the ship structure. It is used to cover the inner space of the ship and divide it horizontally into layers. 6061 aluminum tread plate is an indispensable material for making ship decks, which has has excellent corrosion resistance, weather resistance, anti-slip properties, and is easy to process.

Original Source:https://www.marinealu.com/a/marine-grade-aluminum-6061-for-ship-building.html

5083 Aluminium Plate Used in Cars

 One of the obvious changes in car technology since the 1970s is the extensive use of light materials, and more and more aluminum parts have appeared such as body in white, engine, bumper, air conditioner, wheel hub, and decorative parts ,seat,etc.

The aluminium alloys in automotive industry include 5182, 5083, 5754, 5052, 6061, 6063, 6082 aluminum sheets, which are used in the tank truck, van, coach and passenger cars. They feature good corrosion resistance, good welding performance, good process performance and good coloring performance. Lets have a look of three main applications of 5083 aluminum plate.

Trunk Lid

Generally speaking, the trunk lid of a car has a good elongation and large opening area. It is a necessary passage for passengers to take luggage, tools and other spare items. 5083 aluminum plate has good wear resistance, corrosion resistance and elasticity, and good impact resistance. With low density and light weight, it can reduce the weight of the car body, thus reducing fuel consumption.

Car Pedals

The material used for car pedals generally chooses the material with higher hardness. The aluminum alloy has low density, but the strength is relatively high, which is close to or exceeds that of high-quality steel.

The use of 5083 aluminum alloy for automobile pedals can meet its requirement for the strength for it has high corrosion resistance, good weldability and medium strength,bringing longer service life to the car pedal.

Van Body

The 5083 aluminum for van boday greatly extends the service life of the ruck for the aluminum alloy plate has good oxidation resistance, corrosion resistance and excellent rust resistance. The lightweight van body allow it carry more goods. Welcome to leave message below to inquire aluminum 5083 price.

Original Source:https://www.autoaluminumsheet.com/a/5083-aluminium-plate-used-in-cars.html

The Application of Aluminium En Aw 5083 in LNG Storage Tank

 The aluminium en aw 5083 is widely used in the manufacture of LNG ships and LNG storage tanks, especially in Japan, a country with large liquefied gas. Among them, the main wall structure of the LNG storage tank is 5083 aluminum alloy.

Most aluminum alloys have become important materials for the top structure of storage tanks because of their unique light weight and properties. The use of aluminum alloy to manufacture storage tank top cover has the following characteristics:

1. After the 5083 aluminum alloy is used for the tank top of the LNG storage tank, the weight is greatly reduced, which reduces the load of the tank and its foundation.

2. Aluminum alloy sheet has good corrosion resistance, so it doesn’t need anti-corrosive treatment, which There is no need for maintenance during the use period, which saves a lot of inspection and maintenance costs.

3. The strength of aluminum alloy material is higher at low temperature than normal temperature, and it is an ideal material under low temperature conditions. Therefore, the additional insulation to prevent low temperature brittleness of the material can be omitted during the entire service life.

4. In terms of the actual construction situation, a LNG storage tank is of high economy. It also can reduce the loss of LNG and prevent the liquefied gas from being polluted by water, sand and debris.

5. With a solid roof made of 5083 aluminum plate, it can prevent the the generation of the sparks when it is hit by the direct lightning strike. Haomei aluminum 5083 can fully meets the application materials. Welcome  to leave message below to inquire 5083 aluminum sheet price.

Original source: https://www.aluminumtankerplate.com/a/the-application-of-aluminium-en-aw-5083-in-lng-storage-tank.html

Original Source:https://www.aluminumtankerplate.com/a/the-application-of-aluminium-en-aw-5083-in-lng-storage-tank.html

Aluminum Mirror Strip for Lamp

 The Reflector is the main light control and light distribution device of the lamp. At present, there are many materials used in lamp reflectors, which are roughly divided into two types: diffuse reflection materials and specular reflection materials.

The diffuse reflection material is to make use of the uneven surface of the mirror material to produce diffuse refection effect. The specular reflection material is the aluminum mirror strip got by polishing or anodizing.

The common materials for lamp reflectors are hot rolled aluminum mirror strip, golden aluminum mirror strip and anodized aluminum mirror strip. The reflective effect of the reflector directly affects the quality of the lighting product.

The reflector is an important channel for the heat dissipation of the UV lamp, so the outside of the aluminum cover must be processed into a radiator to increase the heat dissipation area. Therefore, the embossed reflective aluminum strip will be a better choice compared with other reflective materials.

It can increase the surface area of the aluminum plate and have a good heat dissipation effect. After embossing, the strength of the reflective aluminum strip has been strengthened. It also has rich patterns: orange peel, pebble, bean,etc.

Iron or stainless steel cannot be used for the stainless steel plate will turn black at high temperatures, and it will not reflect light, but absorb light. The best reflective material is the anodized aluminum strip, which has a reflectivity of more than 86%. Welcome to leave message below to inquire the reflective aluminium strip.

Original source: https://www.hm-alu.com/a/aluminum-mirror-strip-for-lamp.html

The Aluminium Reflector Sheet For Lighting

 The mirror finish aluminum sheet is widely used in lighting equipment, high-end cosmetics, automobiles or building decoration and exterior wall. In recent years, the solar energy equipment and high-power LED lighting have developed rapidly, and the demand for reflective aluminum sheet has also shown a rapid growth trend.

The aluminum reflector sheet is aluminum plate produced by a rolling method. The surface can achieve a mirror-like effect. Even after anodizing, it can still maintain high finish and high reflectivity, and maintain a high scratch resistance, orrosion resistance and good strength and formability.

At present, the commonly used aluminium mirror sheet is generally 1xxx, 3xxx and 8xxx aluminum. As a reflective material, aluminum reflector sheet for lighting develops in the direction of higher reflectivity (total reflectivity>90%), high thermal conductivity, high scratch resistance and corrosion resistance, and medium strength.

In order to meet the higher requirements of mirror aluminum, Haomei Aluminum has developed 5xxx medium-strength mirror aluminum sheet to meet the high requirements of the LED lighting and solar energy industries.

The 5xxx aluminum reflector sheet is generally produced through a rolling process, and the reflectivity generally reaches 90% or even 95%, which has high requirements on the purity and surface condition. With a strict control of the composition and process, Haomei aluminum mirror sheet fully meets the requirements of the final product. Welcome to leave message below to inquire it.

Original Source: https://www.alumhm.com/a/the-aluminium-reflector-sheet-for-lighting.html

The Versatile 6061 Aluminum Plate

 The marine grade aluminum has great advantages in reducing hull weight, increasing speed and decreasing fuel consumption. 6061 aluminum plate is one of the main alloys for the ship building. At the same time, it also many uses in other fields.

Ship deck

The ship deck is prone to water collection and condensation, directly in contact with the atmosphere, and subject to wind and rain erosion, sun exposure, and the alternating effects of dry and wet seawater.

Therefore, the ship deck is first required to have excellent corrosion resistance, water resistance and weather resistance. In addition, due to personnel activities and mechanical operations, it should have good anti-slip performance. 6061 aluminum tread plate is often used for the ship deck because of its excellent corrosion resistance, weather resistance and slip resistance.

Automobile application

6061 aluminum is often used for the fuel tank, which not only has good corrosion resistance, but also prevents the chemical reaction of oil and external substances. After quenching, 6061 aluminum alloy has good stability and is not easy to deform. It is a good choice for automobile pedals.

Mold

At present, the materials for manufacturing molds on the market include steel, cemented carbide, zinc-based alloys, aluminum alloys, and polymer materials. Compared with other materials, aluminum alloy molds have significant advantages such as light weight, good processing performance, high temperature resistance, and good wear resistance, accounting for 80% of the mold industry.

Manhole cover

It is used to cover deep well on the roads or at home to prevent people or objects from falling. There are many materials for non-slip manhole covers, which can be divided into metal manhole covers, high-strength fiber cement concrete manhole covers, resin manhole covers, and so on. The metal aluminum anti-skid manhole cover can use 6061-t6 aluminum plate.

Bicycle

The bicycle frame is an important mechanical component of the bicycle. Aluminum alloy is currently the most commonly used material in the bicycle market. The bicycle frame made of 6061 aluminum plate has a better advantage than other materials.

Container

Aluminum alloy for containers mainly include 6061, 6082, 6351, 6005, 6063 and 6060 alloys, of which 6061 and 6082 alloys are the most used, accounting for more than 90% of the usage. The product has high strength and good welding performance.

As a reputable aluminium 6061 t6 supplier, Haomei Aluminum has enough production capacity to accept orders with annual production of 200,000 tons. Welcome to leave message below to inquire its price.

Original Source:https://www.marinealu.com/a/the-versatile-6061-aluminum-plate.html

The Aluminum Alloy 5052 Used in Automotive Industry

 Different aluminum alloys have its own properties and is suitable for different parts of the car body. The lightweight and good processability and formability makes aluminum alloy sheet has been a key material of the car lightweight.

Although 5xxx aluminum alloy cannot be strengthened by heat treatment, it has good corrosion resistance and welding performance, which is mainly used for parts with complex shapes such as the inner panel of the car body. AcuraNSX uses aluminum alloy 5052 as the car body and 6000 series as the exterior panel, and JaguarXJ220 and GMEV1 use 5754 aluminum as the body cover material.

The main alloy element of 5052 aluminum sheet is magnesium, which has good forming properties, corrosion resistance, weldability, and medium strength. It can be used for automobile fuel tank, engine outer panels, trunks, car doors, etc., which can improve vehicle performance and decrease fuel consumption.

5052 aluminum plate has a higher strength-to-weight ratio than low-carbon steel. Therefore, 5052 aluminum plates are often used in larger squeezed areas of vehicles, which not only improves safety, but also improves performance. Firstly, the reduction in weight allows shorter stopping distances.Secondly, when comparing the strength-to-weight ratio of metals, 5052 aluminum can absorb the impact energy twice that of low-carbon steel. Therefore, the 5052 aluminum sheet can absorb the energy of the collision and help ensure the safety of passengers. This is extremely important in passenger cars.

Haomei 5052 aluminum alloy has good formability, smooth surface, good weldability and excellent bake hardenability. The lightweight of the automobile also requires the automotive aluminum sheet to have high bake hardenability, that is, the yield strength of the sheet after stamping deformation and paint baking has a significant increase. Welcome to leave message below to inquire 5052 aluminum sheet price.

Original Source:https://www.autoaluminumsheet.com/a/the-aluminum-alloy-5052-used-in-automotive-industry.html

The Main Alloy Used in Aircraft

 The aluminum alloys used in aircraft has a very long history for it can reach high strength after heat treatment, but the weight is very light. It is extremely easy to bend and machined, and of low cost.

The aluminum alloy has become the most commonly used material in modern aviation and is widely used in the manufacture of modern commercial aircraft and military aircraft, such as Boeing 777, Airbus A380, Boeing's UCAV-unmanned aerial combat aircraft and Boeing F/A -18E/F.

Generally speaking, aluminum alloys used as aircraft structural parts are heat-treatable, such as 2xxx, 6xxx and 7xxx aluminum alloy. Among them, 7XXX aluminum alloys such as 7075, 7040, and 7050 aluminum sheet occupy the most important position in aircraft components. Its thickness can range from 0.6 mm to 250 mm.

The 2xxx aluminum has high strength, which is comparable to the steel. However, due to the difference in copper content, the strength and corrosion resistance of 2xxx aluminum alloy vary in a wide range to meet different needs.

Among them, alloys with lower copper content have a corrosion resistance close to that of rust-proof aluminum; alloys with higher copper content have a strength close to duralumin. Due to the higher copper content, 2014 aluminum alloy has higher strength, which is often found in the internal structure or framework of aircraft rather than the shell.

Recently, people pay more attention to how to make the cost of aircraft aluminum alloys decrease through heat treatment. Some aircraft parts manufacturers have tried in the manufacture of such aluminum plates (heat treatment while aluminum is rolled), which are assembled into large ribs and bulkheads after heavy machining.

The advantage of this process is to avoid heat treatment of small parts first and better control of deformation and residual stress, but the disadvantage is that the performance will change along the thickness of the aluminum plate.

Haomei Aluminum has all the main 2xxx and 7xxx aircraft aluminum sheets. Welcome to leave message below to inquire what you need.

Original Source:https://www.aircraftaluminium.com/a/the-main-alloy-used-in-aircraft.html

The Multiple Uses of 5083 aluminum Tanker plate

 Aluminum Alloy Plate for Moss LNG Tank

Aluminum alloy load tanker is a kind of transportation vehicle used to transport various liquids, liquefied gases and powdered goods, including gasoline, crude oil, various viscous oils, vegetable oils, liquid ammonia, wine, water, and various acid-base liquids.

5083 aluminum plate can be applied to oil tanker, natural gas tanker, cement tanker, powder tanker, Moss LNG Tank, etc. Aluminum 5083 h111 is used for the tank body, 5083-O aluminum sheet is used for the tank head, bulkhead and baffle. 5454 aluminum plate is also a popular choice.

ABS plate

5083 aluminum sheet is also widely used for automobile ABS plate. It is often used to make roof panel and fender. If features low density, high strength, strong corrosion resistance and durability. Even if it is exposed to wind, sun, rain, and rain, there will be nor rust and corrosion.

Air Storage Cylinder5083 aluminum plate is also widely used in automobile air storage cylinders. The air storage cylinder is a gas storage device used in the automobile braking system. After being used in automobile air storage cylinders, the 5083 aluminum alloy surface is easy to naturally form a dense and firm layer, extending its service life.

Containers

It is used to load goods for transportation, and is convenient for loading and unloading with mechanical equipment. 5083, 5086, 5052, 5454, 6061, 6082 aluminum plates, etc., are mainly used for the container and vans. The requirements for the aluminum plate for the vans are much lower than that for passenger cars with four doors and two covers.

Shipbuilding

5083 aluminum sheet is corrosion-resistant, durable, and has good arc welding performance. It can also be used to improve its mechanical properties by cold work hardening or heat treatment. It is currently the first choice for hovercraft hull materials.

It can also be used as a raw material for inland water transport hull manufacturing. Marine grade aluminium 5083 is also used in the manufacture of yachts in parks. Aluminum 5083 H116 and 5083 H321 aluminum plate have the best corrosion resistance.

Original Source:https://www.aluminumtankerplate.com/a/the-multiple-uses-of-5083-aluminum-tanker-plate.html

Three Aluminum Alloy Sheets for Closures

 There are mainly three aluminum alloy sheets for closures: 5052, 3105 and 8011. 5052 aluminum strip has excellent deep drawing performance and paint adhesion, ensuring he highest printing and deep stamping quality. It is used as can lid material. Haomei Aluminum can offer color coated or plain aluminum strip.

The surface of 5052 aluminum strip is not allowed to have black spots, corrosion marks, straightening roller marks, oil stains, punctures, scratches, etc. The flatness of the aluminum strip is greater than 10 (or the wave height is less than or equal to 3 mm).

8011 aluminum sheet is often used for PP, ROPP, screw caps of wine bottle, medicinal bottle and injection bottle. Haomei Aluminum can provide different surface processing solutions: ordinary finish-rolled aluminum sheet, DOS oil lubrication treatment, chrome treatment, couble-sided varnish/transparent paint and different colors of two sides.

3105 aluminum alloy plate for closure belongs to the Al-Mg alloy. It has good rust resistance and good deep-drawing effect. The strength, elongation and processing performance of the material can meet the requirements of the automatic production process of high-strength bottle caps, and there will be no creases during processing.

The main thickness of 3105 bottle cap material is 0.15-0.3mm, and the tempers are O, H12, H14, H16, etc. On the basis of ordinary aluminum plate, Haomei Aluminum can chromate the 3105 aluminum plate, do DOS oiling or print various colors.

Which kind of aluminum alloy sheets for closure do you need? Or which kind of caps do you manufacture? We can give you professional tips. Welcome to leave message below to inquire what you need.

Original source: https://www.hm-alu.com/a/three-aluminum-alloy-sheets-for-closures.html